q∝△(T~(-1))传热时三热源热泵的最优性能普遍关系

本文导出工质与三个热源间的传热系数分别为。α、β和γ,传热规律为q~∝△(T~(-1))时,内可逆三热源热泵的最佳供热系数ψ与供热率Π间的关系:ψ<1时,Π=K_1ψ[T_p(T_H-T_ο)-T_H(T_p-Tο)ψ]/[T_HT_pT_ο(1-△_1ψ)~2];ψ>1时,Π=K_2ψ[T_p(T_H-T_ο)-T_H(T_P-T_ο)ψ]/[T_HT_pT_ο(△_2-ψ)~2];式中,K_1=αγ/(α~(1/2)+γ~(1/2))~2,K_2=βγ/(β~(1/2)+γ~(1/2))~2,△_1=(α/β)~(1/2)(β~(1/2)-r~(1/2)/(α~(1/2)+γ~(1/2)),△_2=(β/α)~(1/2)(α~(1/2)-γ~(1/2))/(β~(1/2)+γ~(1/2))。由此可得许多有用的关系。     

信号自屏蔽电荷耦合原理及应用

本文利用静电信号高压电极自身作为传感器的屏蔽电极,使屏蔽深度与仪器灵敏度要求相一致,并使输入端接收的电荷量与被测电位成正比关系,而获得被测电位数值,提出“信号自屏蔽电荷耦合”原理,并从理论上和实验上论述了原理的正确性和先进性。利用此原理研制成ZPD-l型静电电位动态测试仪,该仪器与美制263型高速静电表、日本MH型人体静电电位仪等先进仪器相比,具有输入电阻高(>10~(14)Ω)、动态特性好,抗干扰能力强、高电压非线性失真小等特点。     

Effect of tongue clearance on hydraulic performance of double support vortex pump

In order to study influence of tongue clearance on the hydraulic performance of double support vortex pump, three dimensional flow model with symmetric variable size tongue clearance was established by changing section parameter of tongue clearance, and applied to numerically simulate the steady inner flow in a vortex pump based on fixed working conditions and impeller through ANSYS FLUENT. The numerical results show the influence of tongue channel with two sections (non-uniform and uniform sections) on flow field characteristics in vortex pump. Firstly, the variation of tongue channel section changes the vortex structure distribution in circumferential flow channel. Specifically the spiral forward vortex structure in the circumferential direction shifts to large radius side with increasing tongue width. Secondly, the circumferential velocity gradient and axial pressure gradient both diminish with the increase of the tongue section, and the inlet/outlet pressure difference and velocity distribution also reduce with increasing tongue channel section. Finally, for vortex pump with non-uniform section of tongue channel, the head diminishes and the efficiency remains constant approximately with the increase of the tongue width, while the head and the efficiency both diminish for uniform section of tongue channel.     

海拔高度对发动机泵机组性能的影响

介绍250型泵机组基本参数,详细阐述该型发动机泵机组的动力传递关系,应用FST2E型测试台架开展泵机组发动机高原效能模拟试验,获取发动机在不同海拔高度的功率、燃油消耗率和油耗量数据,拟合生成发动机负荷特性曲线。定量分析不同海拔高度发动机功率下降对离心泵体积流量、效率、扬程等的影响,得出泵机组体积流量、扬程、效率的下降规律。研究结果可为现有泵机组的使用及新型泵机组的研制提供理论依据和数据参考。     

Influence of shaped charge structure parameters on the formation of linear explosively formed projectiles

The research of LEFP (linear explosive forming projectile) is of great value to the development of new warhead due to its excellent performance. To further improve the damage ability of the shaped charge warhead, a special shell overhanging structure was designed to increase the charge based on the traditional spherical charge, in which case the crushing energy of LEFP could be guaranteed. LS-DYNA was used to simulate different charge structures obtained by changing the number of detonation points, the length of shell platform, the radius of curvature and the thickness of liner. The RSM (response surface model) between the molding parameters of LEFP and the structural parameters of charge was established. Based on RSM model, the structure of shaped charge was optimized by using multi-objective genetic algorithm. Meanwhile, the formation process of jet was analyzed by pulsed X-ray photography. The results show that the velocity, length-diameter ratio and specific kinetic energy of the LEFP were closely related to the structural parameters of the shaped charge. After the optimization of charge structure, the forming effect and penetration ability of LEPP had been significantly improved. The experimental data of jet velocity and length were consistent with the numerical results, which verifies the reliability of the numerical results.     

Effects of module number and firing condition on charge thermal safety in gun chamber

Thermal safety of modular charge which is fed into and retained in the chamber after gun fires consecutively is first investigated with cook-off method.A two-dimensional cook-off model of modular charge in gun chamber is established and the cook-off process of modular charge in gun chamber is numerically simulated.Then the effects of module number and firing condition on charge thermal safety are evaluated by researching the cook-off response characteristics of modules.The results show that,under conditions of different module numbers the cook-off responses all occur on the module closest to the boundary of missile,and the single-base propellants located at the inner surface of cartridge ignite first.When the number of loaded module changes from 1 to 6,the cook-off response temperatures vary little,only in a small range of 478.1 K-482.4 K.The cook-off response times decrease logarithmically in the range of 211.2 s-166.7 s with the increasing length of residual air gap in gun chamber.The simulation results are well matched with the experimental data.Furthermore,different firing conditions have great influence on the cook-off response time,minor influence on the initial response position and little in-fluence on the response temperature.Under the three conditions of consecutive 32 launches with 5 rounds/min,43 launches with 1 round/min,and 41 launches with different firing frequencies,the cook-off response temperatures are 479.2 K,481.1 K and 479.9 K respectively and the response times are 709.2 s,211.2 s and 214.4 s respectively.The response position is near the middle area of the inner cartridge surface in the former condition and near the right area in the latter two conditions.     

层流介质中金属板腐蚀电位分布研究

为了研究流动介质中产生的静电场,结合电化学和流体力学相关知识建立层流介质中金属板模型,利用贝塞尔函数展开及其逆运算推导出在三层介质中基于点电荷模型的腐蚀电位解析表达式,同时计算出金属板产生的电场。运用推导出的解析表达式计算出在流动介质中任意场点处金属板随不同流速产生的腐蚀电位,并通过实验验证结果的正确性。结果表明,对层流条件下电化学反应产生的电流密度所建模型的结果与实验测量数据吻合度较高,同时电场分布也会随着流体流速及层流方向上长度的变化而发生变化。     

自动喷水灭火系统水源设施检验应注意的问题

自动喷水灭火系统投入运行后,系统的可靠性则依赖于运行管理,运行管理质量的好坏,决定了自动喷水灭火系统在规定的条件下和规定的时间内完成设计赋予的规定功能的能力。介绍了自动喷水灭火系统水源设施,即消防水池、消防水箱和水泵接合器日常的检验维护,为保证自动喷水灭火系统的正常运行提供了简便可行的方法。     

航空自导深弹和磁探仪攻潜模型与仿真

针对反潜巡逻机使用磁探仪和自导深弹的攻潜效能研究,提出了一种基于蒙特卡洛法的计算模型。在建立攻潜坐标系的基础上,给出了连投深弹射击深度的定义;结合磁探仪定位原理,提出了基于峰值追踪的定位目标和连投攻击的方法,仿真结果表明该方法能够提高命中概率;给出了目标分布和连投深弹的散布模型,依据攻潜过程和命中判定条件,进行了攻潜效能的计算;仿真分析了影响攻潜效能的主要因素,并研究了投弹间隔的确定方法。     

基于探雷信息的火箭深弹炸雷效能研究

针对火箭深弹传统炸雷方式中存在的盲目性、危险性及耗弹量大等问题,提出了火箭深弹与探雷声纳协同定点炸除水雷的方法,建立了基于随机模拟的火箭深弹炸雷效能评估模型。实例解算结果表明,火箭深弹对水雷毁伤概率随着射距的增加而增大;在同一射距下,毁伤概率随射向与探测方向夹角的增加而增大,但在最优(大)夹角附近毁伤概率变化不大。通过该模型能有效解算出火箭深弹对水雷的毁伤效果,进而得到最优射击诸元和最大毁伤概率,对火箭深弹炸雷技术实施提供了理论基础。